Quick answer
A new 1.8m fence in Campbelltown costs about $92 to $135 per metre for Colorbond, $92 to $200 per metre for timber paling, $115 to $170 per metre for an aluminium pool fence and $260 to $920 per metre for glass, installed and including GST. Removal, gates, slope and access are usually extra.
Key takeaways
- Colorbond and treated pine paling are the cheapest full-privacy fences, both from about $92 per metre installed.
- A typical 20m back fence costs $2,200 to $3,500 all up, and each neighbour usually pays half.
- Removal of the old fence adds $20 to $40 per metre, and gates add $350 to $1,600 each.
- Slope, rock, tight access and retaining walls are what push a quote well above the guide price.
- Only a written quote after an on-site measure is a firm price. Guide prices are for budgeting.
How Much Does a New Fence Cost in Campbelltown in 2026?
In 2026, a new fence in Campbelltown costs between $92 and $200 per metre for most boundary fences, installed and including GST. Colorbond and treated pine paling sit at the lower end, hardwood and aluminium slat at the upper end, and glass pool fencing costs the most, from $260 to $920 per metre.
The table below shows guide prices for the fences most often built around Campbelltown, Leumeah, Ingleburn, Minto and the newer Macarthur estates. Each price is per lineal metre of finished fence, supplied and installed, on a clear, reasonably level site. Prices are for 1.8m high boundary fences unless the table says otherwise.
| Fence type | Price per metre | Typical use |
|---|---|---|
| COLORBOND steel, 1.8m | $92 – $135 | Most side and rear boundaries |
| Treated pine paling, butted | $92 – $120 | Budget boundaries and rentals |
| Treated pine, lapped and capped | $115 – $150 | Full privacy at a sensible price |
| Hardwood paling | $135 – $200 | Longer-lasting timber fences |
| Aluminium pool fence, 1.2m | $115 – $170 | Most backyard pools |
| Semi-frameless glass pool fence | $260 – $380 | Pools with a view, on a budget |
| Frameless glass pool fence | $345 – $920 | Uninterrupted views of the pool |
| Aluminium slat, 1.8m | $200 – $320 | Modern privacy and front fences |
| Brushwood, 1.8m | $160 – $330 | Natural garden screens |
| Rural post and wire or rail | $15 – $140 | Acreage and stock fencing |
| Commercial chainwire | $45 – $110 | Yards, depots and building sites |
Scroll sideways to see the full table.
These figures come from the prices published on each of our service pages, which are set to sit at or under the Sydney market. Independent cost guides put most Sydney boundary fences at roughly $86 to $220 per metre, so a quote far outside the ranges above is worth questioning.
What “per metre” means
Fencing is priced per lineal metre: the length of the fence line measured along the ground, not the area of the panels. A 20m back boundary is 20 lineal metres whether the fence is 1.5m or 2.1m high. Height changes the rate per metre, not the number of metres.
What Does a Per-Metre Fence Price Include?
A per-metre fence price normally includes the posts set in concrete, the rails and panels or palings, fixings, labour to install the fence on a clear site, and removal of offcuts and packaging. It normally excludes removing the old fence, gates, plinths for sloping ground, extra height, core drilling and retaining walls.
Usually included
- Posts and footings: steel or H4 treated pine posts set in concrete at each panel or bay
- Infill: COLORBOND sheets, timber palings, aluminium slats, glass panels or mesh
- Rails and capping where the style has them
- Labour to set out the line and build the fence on a clear, reasonably level site
- Clean-up of offcuts, packaging and surplus concrete
- GST, in the prices on this page
Usually extra
- Removing and disposing of the old fence, typically $20 to $40 per metre
- Gates, from $350 for a pedestrian gate to $1,600 for a pair of driveway gates
- Plinths to close gaps under a fence on sloping ground, $20 to $45 per metre
- Extra height, such as a lattice or slat extension, $45 to $75 per metre
- Core drilling posts into concrete or pavers, $25 to $70 per post
- Retaining walls where the ground needs holding back before a fence can go in
Read every quote line by line. Two quotes with the same per-metre rate can end up hundreds of dollars apart once removal, gates and plinths are added. A good quote lists each of these separately so you can compare like with like.
How Much Does a Colorbond Fence Cost in Campbelltown?
A COLORBOND steel fence in Campbelltown costs $92 to $135 per metre at the standard 1.8m height, $85 to $110 per metre at 1.5m, and $115 to $160 per metre at 2.1m, installed and including GST. All 15 colours cost the same. Plinths, extensions, gates and removal are extra.
| Height | Price per metre | Notes |
|---|---|---|
| 1.5m | $85 – $110 | Low side fences and returns |
| 1.8m (standard) | $92 – $135 | Most side and rear boundaries |
| 2.1m | $115 – $160 | Extra privacy; usually needs council approval |
Scroll sideways to see the full table.
Colorbond is the most common boundary fence in the newer Macarthur estates because it is quick to install, needs no painting, and resists termites and rot. The price range reflects panel profile, post spacing, ground conditions and how many corners and gates the fence has.
| Extra | Price |
|---|---|
| Concrete plinths on sloping ground | $25 – $45 per metre |
| Height extension, about 300mm | $45 – $75 per metre |
| Single COLORBOND pedestrian gate | $350 – $650 each |
| Double COLORBOND driveway gates | $900 – $1,600 per pair |
| Remove and dispose of the old fence | $20 – $40 per metre |
See current prices, colours and options on our Colorbond fencing page, or compare the two most popular materials in our Colorbond vs timber guide.
How Much Does a Timber Paling Fence Cost?
A 1.8m timber paling fence in Campbelltown costs $92 to $120 per metre for treated pine with butted palings, $115 to $150 per metre lapped and capped, and $135 to $200 per metre in hardwood, installed and including GST. Galvanised steel posts add about $15 to $25 per metre.
| Style | Price per metre | Best for |
|---|---|---|
| Treated pine, butted palings | $92 – $120 | Budget boundary fences and rentals |
| Treated pine, lapped and capped | $115 – $150 | Full privacy at a sensible price |
| Hardwood, butted palings | $135 – $175 | A longer-lasting standard fence |
| Hardwood, lapped and capped | $160 – $200 | Premium privacy and the longest palings |
| Exposed-post feature fence | $190 – $220 | Street-facing and feature fences |
Scroll sideways to see the full table.
Butted palings sit side by side, so small gaps open as the timber dries. Lapped and capped palings overlap and are finished with a capping rail, which costs more but gives full privacy for longer. Hardwood such as spotted gum or blackbutt costs about a third more than treated pine and lasts longer in the ground and in the weather.
Timber is also the only common material that can be repaired one board at a time, which keeps long-term costs down. See styles and prices on our timber fencing page.
How Much Does Pool Fencing Cost in Campbelltown?
An aluminium pool fence in Campbelltown costs $115 to $170 per metre, semi-frameless glass costs $260 to $380 per metre, and frameless glass costs $345 to $600 per metre on spigots, up to $920 per metre with a concealed channel, installed and including GST. A compliant self-closing gate adds $350 to $1,000.
| Pool fence | Price per metre | Notes |
|---|---|---|
| Aluminium flat-top, 1.2m | $115 – $165 | Best value; most common |
| Aluminium tubular, 1.2m | $120 – $170 | Softer, rounded look |
| Semi-frameless glass | $260 – $380 | Slim aluminium posts |
| Frameless glass, core-drilled spigots | $345 – $600 | The most popular glass option |
| Frameless glass, base plates or side mounts | $420 – $700 | Decks, slabs and retaining walls |
| Frameless glass, concealed channel | $550 – $920 | No visible hardware |
Scroll sideways to see the full table.
Every pool fence in NSW must meet Australian Standard AS 1926.1, so pool fencing is priced for compliance as well as looks. Gates are the most expensive single item: an aluminium self-closing, self-latching gate costs $350 to $600, and a glass gate with soft-close hinges costs $650 to $1,000.
A typical backyard pool needs 20 to 30 metres of barrier plus one gate. The rules are explained in our NSW pool fence rules guide. For prices and options, see pool fencing and glass pool fencing.
What Do Aluminium Slat, Brushwood, Rural and Commercial Fences Cost?
Aluminium slat fencing costs $200 to $320 per metre at 1.8m, brushwood costs $160 to $330 per metre, rural post and wire costs $15 to $35 per metre and post and rail $55 to $140 per metre, and commercial chainwire costs $45 to $110 per metre, installed and including GST.
| Fence | Price per metre | Read more |
|---|---|---|
| Aluminium slat, 1.8m, 65mm blades | $200 – $280 | Aluminium & slat |
| Aluminium slat, 1.8m, 90mm blades | $230 – $320 | Aluminium & slat |
| Brushwood panels on steel posts | $160 – $240 | Brushwood |
| Hand-thatched brushwood | $230 – $330 | Brushwood |
| Rural post and wire | $15 – $35 | Rural & acreage |
| Rural post and rail | $55 – $140 | Rural & acreage |
| Commercial chainwire, 1.8m | $45 – $110 | Commercial |
| 358 anti-climb security mesh | $220 – $380 | Commercial |
Scroll sideways to see the full table.
Slat fencing costs more because aluminium blades and channel posts are priced per blade, and the gap between blades decides how many blades you need. Rural fencing is cheap per metre because long runs of wire go up quickly, but the strainer assemblies at corners and gates add to the total.
What Makes a Fence Cost More?
The biggest cost drivers for a fence in Campbelltown are sloping ground, rock or tree roots along the line, tight access, removal of an old fence, the number of gates and corners, extra height, and any retaining wall needed first. Each of these adds labour or materials that a basic per-metre price does not cover.
| Cost driver | Typical cost | Why it costs more |
|---|---|---|
| Old fence removal | $20 – $40 per metre | Labour, tip fees, asbestos checks on old fibro fences |
| Sloping ground | $20 – $45 per metre | Stepping panels and plinths to close gaps |
| Rock or roots | Quoted on site | Slower digging, rock drilling |
| Tight access | Quoted on site | Materials carried in by hand |
| Gates | $350 – $1,600 each | Heavier posts and hardware |
| Height extension | $45 – $75 per metre | Extra materials and fixing |
| Retaining wall | $220 – $700 per metre | A separate structure, often engineered |
Scroll sideways to see the full table.
Slope and retaining walls
Many blocks in Glen Alpine, Kentlyn, Minto Heights and parts of Bradbury slope across the fence line. A fence on a slope is either stepped, with level panels and plinths filling the triangular gaps, or raked to follow the ground. Both add cost, and where the ground on one side is much higher, a retaining wall may be needed first. Our sloping block guide explains the options.
Old fibro fences
Asbestos in old fences
Some fences built before the late 1980s are fibro sheeting that may contain asbestos. Don’t break or cut it. Removal must be done safely by a licensed removalist where required, and is quoted separately. If your old fence is fibro, mention it when you book the measure.
Access and site conditions
If a truck can reach the fence line and the ground is clear, installation is fastest. Narrow side paths, steep driveways, garden beds against the fence and large trees on the line all slow the job. Clearing the line yourself before the installer arrives is one of the easiest ways to keep costs down.
What Does a Typical Fencing Job Cost in Campbelltown?
A typical 20m Colorbond back fence in Campbelltown costs $2,200 to $3,500 including removal of the old fence, a 30m lapped and capped timber side fence with steel posts and a gate costs about $4,250 to $5,900, and a 24m aluminium pool fence with one gate costs about $3,400 to $5,000, installed and including GST.
Example 1: 20m Colorbond back fence, shared with a neighbour
A level rear boundary in Ruse or Leumeah, replacing an old paling fence with 1.8m COLORBOND steel. The cost is split 50/50 with the neighbour.
- 20m COLORBOND, 1.8m
- $1,840 – $2,700
- Remove the old fence
- $400 – $800
- Total job
- $2,240 – $3,500
- Each neighbour pays
- $1,120 – $1,750
Example 2: 30m lapped and capped timber side fence
A side boundary in an established street in Bradbury, built in treated pine with galvanised steel posts, with one pedestrian gate.
- 30m lapped and capped pine
- $3,450 – $4,500
- Galvanised steel posts upgrade
- $450 – $750
- Timber pedestrian gate
- $350 – $650
- Total job
- $4,250 – $5,900
Example 3: aluminium pool fence for a new pool
A rectangular pool in a Gregory Hills backyard needs 24m of 1.2m aluminium flat-top barrier and one self-closing gate, with posts core-drilled into the pool surround.
- 24m aluminium pool fence
- $2,760 – $3,960
- Self-closing, self-latching gate
- $350 – $600
- Core drilling, about 10 posts
- $250 – $450
- Total job
- $3,360 – $5,010
These examples use the guide prices on this page for straightforward sites. Slope, rock, access and extra gates move the final figure, which is why every job is measured before it is quoted.
How Much Does Each Neighbour Pay for a Dividing Fence?
Under the Dividing Fences Act 1991 (NSW), neighbours usually pay equal shares of a “sufficient” dividing fence, so each pays half. If one neighbour wants something dearer, such as a taller fence or a premium material, they usually pay the difference. Councils and other public authorities are not required to contribute.
For a $3,000 standard back fence, each neighbour usually pays $1,500. If your neighbour is happy with a standard 1.8m Colorbond fence and you want 2.1m, you would typically pay the extra cost of the taller fence yourself. The same applies if you want lapped and capped hardwood where treated pine butted palings would be a sufficient fence.
- Agree the fence type, height, colour and cost in writing before work starts
- If you can’t agree, serve a written fencing notice with a quote attached
- If there’s no agreement after one month, either neighbour can apply to NCAT or the Local Court
- Urgent repairs, such as after a storm, can be done first and the share claimed afterwards
The full process, including what to do if your neighbour won’t pay, is in our guide Who Pays for a Boundary Fence in NSW? An itemised quote that shows each neighbour’s share makes the conversation much easier.
How Can You Keep the Cost of a New Fence Down?
The best ways to save on a new fence are to choose a standard 1.8m height and a standard material, agree on the fence with your neighbour early so the cost is shared, clear the fence line before the installer arrives, and fence several boundaries in one job so set-up costs are spread across more metres.
Choose standard sizes
A 1.8m fence uses standard panel and paling lengths. Taller fences, custom colours and unusual post spacing all cost more.
Share the cost properly
Talk to your neighbour before you get quotes. A dividing fence is normally split 50/50.
Do several boundaries at once
Delivery, set-out and travel are paid once, so the per-metre rate often drops on bigger jobs.
Clear the line
Move pots, cut back plants and clear rubbish along the fence so the crew can start straight away.
Keep sound parts
If the posts are solid, a repair or re-sheet can cost far less than a full replacement.
Compare like with like
Get quotes that list removal, gates and plinths separately so a low headline rate doesn’t hide extras.
Avoid saving money by skipping footings, using lighter posts or leaving the fence off the boundary line. These shortcuts tend to cost more within a few years, and a fence in the wrong place can cause a dispute when either property is sold.
How Do You Get an Accurate Fence Quote in Campbelltown?
To get an accurate fence quote, book an on-site measure, show the installer the exact boundary, slope, access and any gates you need, and ask for a written, itemised quote. In NSW, residential fencing work worth more than $5,000 must be done by a licensed contractor under a written contract, with a deposit of no more than 10%.
What a good fence quote lists
- the contractor’s name, ABN and NSW contractor licence number
- the fence type, height, length, colour or timber, and post type
- removal of the old fence, plinths, gates and hardware as separate lines
- the total including GST, and the payment schedule
- the expected start date and the workmanship warranty
Rules that protect you
- Licence: check any contractor on the NSW Government licence check before you sign
- Written contract: required for residential work over $5,000, including GST
- Deposit: no more than 10% of the contract price for residential building work
- Variations: any change to the agreed work should be agreed in writing before it’s done
You can check a contractor’s licence with the NSW Government licence check (opens in a new tab). When you request a free quote through us, a licensed local installer measures the job and gives you a fixed, itemised written price, usually within 24 hours.
Is It Cheaper to Repair or Replace a Fence?
Repairing is cheaper when the posts are still sound and only panels, palings or a gate are damaged. Small repairs start from about $180. Replacing makes more sense when several posts have rotted, rusted or moved, because new infill on failing posts won’t last and the repair bill soon approaches the cost of a new fence.
| Repair | Typical price |
|---|---|
| Small repair (minimum charge) | from $180 |
| Replace one COLORBOND sheet | $150 – $300 |
| Replace a full COLORBOND panel | $280 – $480 |
| Replace timber palings | $60 – $130 per metre |
| Straighten a leaning post | $200 – $420 |
| Replace a fence post | $250 – $480 |
A useful test: push gently on each post. If most are firm and only one or two lean, a repair is usually the better value. If posts move along most of the fence, or the timber at ground level is soft, replacement is usually cheaper over the next ten years. Storm damage is often covered by home insurance, which is explained in our storm damaged fence guide. For repair prices, see fence repairs.
Frequently Asked Questions
Are fence prices quoted with or without GST?
Prices for homeowners should include GST, and every price in this guide does. Some trade and commercial quotes are written excluding GST, which makes them look 10% cheaper, so check the total line on every quote before you compare them.
Why do fence quotes vary so much for the same job?
Usually because they include different things. One quote may include removal, plinths and a gate while another lists them as extras, or uses lighter posts and wider spacing. Compare the itemised lines, post type, footing depth and warranty, not just the total.
Does the fencer charge to take away the old fence?
Usually, yes. Removing and disposing of an old fence typically costs $20 to $40 per metre, depending on the material and access. Old fibro fences that may contain asbestos are quoted separately because they must be removed safely.
Does a sloping block cost more to fence?
Yes. Panels have to be stepped or raked to follow the ground, and plinths are usually needed to close the gaps underneath, adding about $20 to $45 per metre. Steep blocks may also need a retaining wall before a fence can go in.
How long does it take to get a fence quote?
After you book, the installer measures the site at a time that suits you. A written, itemised quote usually follows within 24 hours of the measure. Simple repairs can often be priced from photos first.
When do I pay for a new fence?
Typically a small deposit when you sign, then the balance when the fence is finished. In NSW, a contractor can’t ask for a deposit of more than 10% of the contract price for residential building work, so be wary of anyone asking for full payment up front.
Sources
- Independent Sydney fencing cost guide (What’s The Damage, 2026) (opens in a new tab)
- Home Building Act 1989 (NSW): licensing, contracts and deposits (opens in a new tab)
- Checking your contractor is licensed (NSW Government) (opens in a new tab)
- Fences, boundaries and retaining walls (Legal Aid NSW) (opens in a new tab)
- Exempt development: fences (NSW Planning Portal) (opens in a new tab)