Pool safety guide

NSW Pool Fence Rules Explained

Every measurement in the NSW pool barrier rules explained in plain English: heights, gaps, the non-climbable zone, gates and latches, boundary fences, older pools and spas, and the faults inspectors find most often.

  • Updated 20 November 2026
  • 11 min read
  • Checked against AS 1926.1-2012

Quick answer

In NSW, a pool deeper than 300mm must be surrounded by a child-resistant barrier that meets AS 1926.1. The fence must be at least 1200mm high, with gaps no wider than 100mm, no climbable objects within the 900mm non-climbable zone, and a gate that swings away from the pool and closes and latches by itself.

Key takeaways

  • Any pool or spa that can hold 300mm or more of water needs a compliant barrier and must be on the NSW Swimming Pool Register.
  • The key numbers: 1200mm minimum height, 100mm maximum gap, and a 900mm non-climbable zone.
  • Gates must swing away from the pool, self-close from any position and self-latch, with the latch at least 1500mm above the ground.
  • A boundary fence used as a pool barrier must be at least 1800mm high.
  • Older pools are generally checked against the standard in force when they were built, until the barrier is altered.

What Are the Pool Fence Rules in NSW?

Pool fencing in NSW is governed by the Swimming Pools Act 1992 and its regulation, which require a child-resistant barrier around any pool or spa that can hold 300mm or more of water. For pools built since May 2013, the barrier must meet Australian Standard AS 1926.1-2012, which sets the heights, gaps, gate and latch rules.

The law puts the duty on the pool owner. Whether you own the home or rent it out, the owner must keep the barrier compliant and in good repair at all times, register the pool, and display a resuscitation (CPR) sign near the pool. Councils inspect pools, and certifiers issue the compliance certificates needed when a home with a pool is sold or leased.

NSW pool barrier rules at a glance (AS 1926.1-2012)
RequirementMeasurement
Minimum barrier height1200mm, measured on the outside
Gap under the barrierNo more than 100mm
Gaps between vertical bars or panelsNo more than 100mm
Non-climbable zone900mm, measured from the top of the barrier
Inside clear zone (pool side)300mm
Gate latch heightAt least 1500mm above the ground
Boundary fence used as a barrierAt least 1800mm high
Pools coveredAny pool or spa 300mm deep or more

These numbers come from the Australian Standard, which is detailed and technical. The sections below explain what each one means on a real fence in a Campbelltown backyard, and what to check before an inspection.

How High Must a Pool Fence Be in NSW?

A pool fence in NSW must be at least 1200mm high, measured from finished ground level on the outside of the fence. Where a boundary fence forms part of the pool barrier, it must be at least 1800mm high. The height must hold along the whole fence, including at low points, garden beds and steps.

Height is measured from the ground a child would stand on outside the pool area, not from the pool side. If soil, mulch or pavers build up against the fence over the years, the effective height drops. A fence that measured 1200mm when it was installed can fail an inspection later because the ground around it has risen.

  • Measure at several points, especially beside garden beds, retaining walls and steps
  • Watch for raised ground such as a new paver edge, a sleeper border or a pile of soil
  • Glass panels must also be at least 1200mm above the finished surface, not the spigot base
  • Boundary fences used as part of the barrier must be 1800mm, because the neighbour’s side can’t be controlled

Most new pool fences are built taller

Aluminium pool fence panels are commonly 1200mm to 1250mm high and set a little above the ground, so the top sits comfortably above the minimum. Building with a margin means a small rise in the ground won’t make the fence fail.

What Gaps Are Allowed in a Pool Fence?

No gap in a NSW pool fence may be wider than 100mm. That applies to the gap between the bottom of the fence and the ground, the gaps between vertical bars, and the gap between glass panels. Horizontal rails a child could climb must be at least 900mm apart, otherwise they must be on the pool side of the fence.

The 100mm rule exists because a young child’s head and body can fit through a gap any wider. Inspectors use a test object to check the gaps, so a fence that looks fine can still fail where pavers have sunk, soil has washed away or a panel has been knocked out of line.

Common gap problems

  • Under the fence: erosion, settled pavers or a sloping lawn can open the bottom gap past 100mm
  • Beside the gate: the gaps at the hinge and latch sides grow as hinges wear
  • Between panels: glass or aluminium panels that have shifted after a knock
  • Under garden edging: where the fence crosses a garden bed or drain

Horizontal rails

A horizontal rail is a foothold. On the outside of a pool fence, climbable horizontal members must be at least 900mm apart, so a child can’t use them like a ladder. Standard aluminium pool fence panels are designed with their rails in the right places. Problems usually come from add-ons, such as screening battens or a timber frame fixed to the outside of the fence.

What Is the Non-Climbable Zone Around a Pool Fence?

The non-climbable zone is a 900mm area measured from the top of the pool fence, in which there must be nothing a child could use to climb over: no footholds, pots, chairs, barbecues, trees, retaining walls or taps. On the pool side, there must also be a 300mm clear zone below the top of the fence.

Think of the zone as an arc reaching 900mm out from the top of the fence on the outside. Anything inside that arc that a small child could step on is a climbing aid. The zone moves with the fence, so it applies along its whole length, including corners and gates.

Garden and furniture

Pot plants, outdoor chairs, eskies, toys and barbecues are the most common climbing aids found at inspections.

Built features

Retaining walls, steps, letterbox posts, taps, air-conditioning units and window ledges can all be footholds.

Plants and trees

Shrubs and branches that grow into the zone count too. Keep them trimmed back from the fence.

Boundary fences

On a boundary barrier, the 900mm zone is measured down from the top on the inside, because the neighbour’s side can’t be controlled.

The zone is the part of compliance most likely to change after the fence is built, because it depends on how the yard is used. A quick walk around the fence before summer, moving anything within 900mm, prevents most failed inspections.

What Are the Rules for Pool Gates and Latches?

A pool gate in NSW must swing outward, away from the pool, close by itself from any open position, and latch by itself without anyone touching it. The latch release must be at least 1500mm above the ground. If it is lower, it must be on the pool side of the gate and shielded so a child can’t reach through.

  1. Swings away from the pool

    The gate opens outward, so a child pushing on it from outside can’t open it into the pool area.

  2. Self-closes from any position

    Open the gate fully, let go and it must close. Then try it from half open and just ajar.

  3. Self-latches

    The latch must engage on its own every time, without the gate being pushed shut.

  4. Latch out of reach

    The latch release sits at least 1500mm high, or on the pool side, shielded, if it is lower.

  5. Never propped open

    A gate held open by a brick, chair or tie is a breach, even for a few minutes.

Gates fail more inspections than any other part of a pool fence, because springs weaken, hinges sag and latches drift out of line. Test the gate every month from fully open, half open and a few centimetres open. If it sticks at any point, adjust or replace the hinges before the next inspection.

New self-closing hinges and a latch on an existing gate typically cost $180 to $350, and a new self-closing, self-latching aluminium gate costs $350 to $600. Glass gates with soft-close hinges cost $650 to $1,000. See pool fencing for options.

Can a Boundary Fence Be Part of a Pool Barrier?

Yes. A boundary fence can form part of a NSW pool barrier if it is at least 1800mm high, has no gaps wider than 100mm, and has a 900mm non-climbable zone on the pool side measured down from the top. Rails or footholds within that zone on the inside must be removed, covered or moved.

COLORBOND steel and lapped and capped timber fences at 1800mm are often used as part of a pool barrier along the back or side of the yard. The catch is the inside face: horizontal rails, capping or a plinth on the pool side can create footholds inside the top 900mm. Many COLORBOND fences have their rails on one side, so it matters which way the panels face.

  • Check the fence is at least 1800mm high along the whole pool-area section
  • Look for rails, brackets or capping on the pool side within 900mm of the top
  • Make sure the neighbour’s side has no gaps under the fence wider than 100mm
  • Keep plants, pots and play equipment away from the inside of the fence

Who pays for a boundary fence that is also a pool barrier?

Under the Dividing Fences Act, neighbours usually share the cost of an ordinary dividing fence. Where the fence must also meet the pool barrier rules, Legal Aid NSW explains that the pool owner generally pays for the pool barrier part, and if both neighbours have pools sharing the fence, the cost is split in proportion. Our guide Who Pays for a Boundary Fence in NSW? covers the process.

Can a House Wall, Door or Window Be Part of the Barrier?

For pools built under the current rules, the barrier must separate the pool from the house, so a door should not open straight into the pool area. Some older pools were allowed to use the house wall, with restricted doors and windows instead of a fence. Those arrangements must still be kept compliant, and change if the barrier is altered.

Before 1 July 2010, NSW law gave some pools an alternative to a full barrier: pools on very small blocks (under 230 square metres), very large blocks (2 hectares or more) and waterfront properties could restrict access from the house instead. Pools whose construction began before 1 August 1990 also had an exemption. These exemptions only continue while access stays restricted as the rules required.

Changing the barrier changes the rules

If an older pool barrier is substantially altered, rebuilt or replaced, the current rules and AS 1926.1-2012 apply, and earlier exemptions can be lost. Check with council or a certifier before you renovate around a pool.

If you’re not sure how your pool was approved, Campbelltown City Council or a pool certifier can tell you which rules apply to it. Our guide to pool compliance certificates explains inspections.

Which Rules Apply to Older Pools?

In NSW, a pool barrier is generally assessed against the Australian Standard in force when the pool was built: AS 1926-1986 for pools built before 30 August 2008, AS 1926.1-2007 for pools built from 1 September 2008 to 30 April 2013, and AS 1926.1-2012 for pools built since. Altering the barrier brings in the current standard.

Which pool barrier standard applies, by construction date
Pool builtStandard usually applied
Before 30 August 2008AS 1926-1986
1 September 2008 – 30 April 2013AS 1926.1-2007
From 1 May 2013AS 1926.1-2012
Barrier altered or rebuiltCurrent rules and AS 1926.1-2012

This is why two pools in the same street can be judged by slightly different standards. It isn’t a loophole: the barrier still has to be child-resistant, in good repair and fully compliant with its standard. A certifier checks the approval history before deciding which standard to inspect against.

Campbelltown has many older pools

Established suburbs such as Bradbury, Ruse, Leumeah and Ambarvale have many pools built in the 1980s and 1990s. These often need gate hardware, gaps or climbable objects fixed before a sale, rather than a whole new fence.

Do Spas, Inflatable and Above-Ground Pools Need a Fence?

Yes, if they can hold 300mm or more of water. In NSW, the pool barrier rules apply to spas, above-ground pools and portable or inflatable pools of that depth, not only in-ground pools. Spa pools may use a lockable, child-safe cover instead of a fence where the rules allow it, and must be registered.

  • Inflatable and portable pools: once they can hold 300mm, they need a barrier and registration, even if they are only up for summer
  • Above-ground pools: the pool wall can sometimes act as the barrier if it is high and non-climbable, but ladders and steps must be removable or enclosed
  • Spas: a lockable, child-safe lid can be an alternative to a fence where it meets the requirements; it must be locked whenever the spa isn’t in use
  • Water features and ponds: generally not swimming pools unless they are used for swimming or wading

Under 300mm, a portable pool isn’t covered by the barrier rules, but it should always be emptied after use and supervised. Children can drown in very shallow water.

Do You Have to Register Your Pool and Display a CPR Sign?

Yes. Every pool and spa in NSW that is 300mm deep or more must be registered on the NSW Swimming Pool Register, which is free online. A resuscitation (CPR) sign must also be displayed in a prominent place near the pool. A registration certificate is needed when a property with a pool is sold or leased.

  1. Register online

    Register on the NSW Swimming Pool Register (opens in a new tab). It is free and takes a few minutes.

  2. Self-assess the barrier

    The register includes a checklist to help you check your barrier against the rules.

  3. Display a CPR sign

    Use a current resuscitation sign, mounted where it can be seen from the pool.

  4. Keep records

    Keep your registration and any compliance certificates with the property documents.

What Fails a Pool Fence Inspection Most Often?

The most common reasons a pool fence fails an inspection in NSW are a gate that doesn’t self-close or self-latch, climbable objects inside the 900mm non-climbable zone, gaps under the fence wider than 100mm, a missing or out-of-date CPR sign, and damaged or loose panels. Most are cheap to fix.

Common pool fence faults and typical fixes (guide prices incl. GST)
FaultTypical fixGuide cost
Gate doesn’t self-close or latchNew hinges and latch$180 – $350
Worn-out gateNew self-closing aluminium gate$350 – $600
Gap under fence over 100mmRaise panels or add a plinthQuoted on site
Pots, chairs or plants in the zoneMove or trim themFree
Missing CPR signInstall a current signAbout $30 – $60
Damaged panels or postsReplace panels or reset postsQuoted on site

Scroll sideways to see the full table.

Before an inspection, walk the fence with a tape measure, test the gate from every position, and clear the non-climbable zone. If anything needs a tradesperson, fix it first: a re-inspection costs more time and money than doing it right before the visit.

Which Pool Fence Types Meet the NSW Rules?

Aluminium, frameless glass, semi-frameless glass and tubular steel pool fences can all meet the NSW rules when they are installed to AS 1926.1 with compliant gates. In Campbelltown, aluminium pool fencing costs $115 to $170 per metre and frameless glass $345 to $600 per metre on spigots, installed and including GST.

Compliant pool fence options in Campbelltown (guide prices incl. GST)
FencePrice per metreGood to know
Aluminium flat-top, 1.2m$115 – $165Best value, easy to keep compliant
Aluminium tubular, 1.2m$120 – $170Rounded tops, same rules
Semi-frameless glass$260 – $380Slim posts, open views
Frameless glass on spigots$345 – $600Uninterrupted views

Scroll sideways to see the full table.

Glass fences meet the same rules as aluminium: 1200mm high, gaps no wider than 100mm, and a self-closing, self-latching glass gate. Toughened safety glass is used. For more, see our pool fencing and glass pool fencing pages.

Frequently Asked Questions

Can I have plants near my pool fence?

Yes, but nothing a child could climb within the 900mm non-climbable zone, and branches must not grow over or through the fence. Low ground covers are fine. Trim shrubs regularly, because a plant that was small at installation can become a climbing aid within a few years.

Does a new pool fence need council approval?

A new pool usually needs council approval or a complying development certificate, and the barrier is part of that approval. Replacing an existing pool fence on the same line may not need a new approval, but it must meet the current rules. Check with Campbelltown City Council first.

Is a glass pool fence safe and compliant?

Yes, when it is built from toughened safety glass and installed to AS 1926.1, with gaps no wider than 100mm and a self-closing, self-latching gate. Glass has no rails to climb, which makes the non-climbable zone easier to keep clear.

Who is responsible for the pool fence in a rental?

The owner. The Swimming Pools Act puts the duty to keep the barrier compliant on the property owner, and a property with a pool can’t be leased without a valid certificate of compliance. Tenants should report a broken gate or fence to the agent straight away.

Do I need a fence for a pool that is still being built?

Yes. A pool under construction must be fenced off as soon as it can hold water, and builders usually use temporary pool fencing until the permanent barrier is installed. Never fill a pool before a compliant barrier is in place.

What happens if my pool fence doesn’t comply?

Council can direct you to fix the barrier and can issue fines. If the property is being sold or leased, a non-compliant fence must be fixed before a certificate of compliance is issued, or the buyer takes on the work within set time limits.

Sources

  1. Swimming Pools Act 1992 (NSW) (opens in a new tab)
  2. NSW Swimming Pool Register (opens in a new tab)
  3. Pool fencing (Campbelltown City Council) (opens in a new tab)
  4. AS 1926.1-2012 Swimming pool safety: safety barriers (Standards Australia) (opens in a new tab)
  5. Fences, boundaries and retaining walls (Legal Aid NSW) (opens in a new tab)

Related services and guides