Quick answer
Most standard fences in Campbelltown don’t need council approval, because they are exempt development under the NSW Codes SEPP. A side or rear fence up to 1.8m and a front fence up to 1.2m usually qualify, if they meet the rules on materials, gates and corner blocks. Taller fences, heritage properties and some bush fire prone land need approval.
Key takeaways
- Most side and rear fences up to 1.8m, and front fences up to 1.2m, are exempt development: no approval needed.
- Exempt fences still have to meet rules on materials, gates, corner blocks and bush fire prone land.
- Taller fences, such as a 2.1m side fence, usually need a development application or a complying development certificate.
- Exempt development can’t be carried out on State Heritage Register properties.
- Council approval and your neighbour’s agreement are separate: you may need both.
Do You Need Council Approval to Build a Fence in Campbelltown?
Usually not. Most fences in Campbelltown are exempt development under the State Environmental Planning Policy (Exempt and Complying Development Codes) 2008, so they need no approval if they meet its rules. You need approval when a fence is taller than the limits, doesn’t meet the other standards, or is on land where exempt development isn’t allowed.
The Codes SEPP, as it’s usually called, is a NSW-wide planning policy. It sets out types of minor work, including fences, that can be done without a development application, as long as every standard is met. If even one standard isn’t met, the fence is no longer exempt and needs approval.
| Pathway | When it applies | Who approves |
|---|---|---|
| Exempt development | The fence meets every Codes SEPP standard | No approval needed |
| Complying development certificate (CDC) | The fence meets the complying development standards | Council or a registered certifier |
| Development application (DA) | The fence doesn’t fit either code | Campbelltown City Council |
Scroll sideways to see the full table.
What Does “Exempt Development” Mean for a Fence?
Exempt development is minor building work that doesn’t need planning or building approval because it meets pre-set standards in the Codes SEPP. For fences, those standards cover height, position, materials, transparency on corner blocks, gates and bush fire prone land. If the fence meets them all, you can build without telling council.
Exempt doesn’t mean anything goes. An exempt fence still has to be structurally adequate, installed to the manufacturer’s instructions and comply with the Building Code of Australia. It also doesn’t change your obligations to your neighbour under the Dividing Fences Act 1991.
- no development application or certificate is needed
- there are no council fees for approval
- every standard must be met, not just the height
- the work must still be safe, sound and built properly
What Rules Must an Exempt Fence Meet in NSW?
In residential zones, an exempt side or rear fence can be up to 1.8m high, or 1.2m if it’s masonry. Front fences, and side fences on the street side of corner blocks, can be up to 1.2m. Gates must not open outwards, metal parts must be low-reflective and factory pre-coloured, and barbed wire and electric fencing aren’t allowed.
| Rule | Standard |
|---|---|
| Side and rear boundary fences | Up to 1.8m (1.2m if masonry) |
| Front fences and street-side fences on corner blocks | Up to 1.2m |
| Street-side fences on corner blocks (secondary road) | At least 20% transparent above 400mm; solid piers no wider than 350mm |
| Fences stepped on a slope | Up to 2.2m at each step (1.5m where the limit is 1.2m) |
| Gates | Must not open outwards |
| Metal parts | Low-reflective, factory pre-coloured |
| Barbed wire and electric fencing | Not allowed (except in zone R5) |
| Bush fire prone land | Non-combustible materials or hardwood |
Rural zones have their own rules, including post and wire or post and rail fences up to 1.8m, and business and industrial zones allow fences up to 3m. Every height rule, including corner blocks and slopes, is explained in our fence height rules guide.
COLORBOND meets the materials rule
Factory pre-coloured steel such as COLORBOND meets the low-reflective, pre-coloured rule for metal parts. Bare galvanised steel or reflective materials may not.
When Does a Fence Need Council Approval?
A fence needs approval when it’s taller than the exempt limits, such as a 2.1m side fence or a 1.5m front fence; when it doesn’t meet the corner-block, material, gate or bush fire standards; when it’s on a State Heritage Register property; when it includes barbed wire or electric fencing in a residential zone; or when it’s on public land.
Common fences that usually need approval
- Taller boundary fences: a 2.1m COLORBOND fence for extra privacy
- Taller front fences: anything over 1.2m at the front or on the street side of a corner block
- Solid front fences on corner blocks: that don’t meet the transparency rule
- Masonry fences over 1.2m, such as rendered brick walls
- Fences on heritage properties listed on the State Heritage Register
- Retaining walls on the boundary that a fence will sit on
- Fences on or over public land, such as a footpath, which also need Roads Act approval
A new swimming pool and its barrier are approved together, so the pool fence is covered by the pool’s approval. Our NSW pool fence rules guide explains the barrier requirements.
What About Heritage Properties and Conservation Areas?
Exempt development can’t be carried out on land or buildings on the State Heritage Register or under an interim heritage order, so fences there need approval. Local heritage items and heritage conservation areas listed in Campbelltown’s planning controls can also have their own requirements. Check with council before changing a fence on a heritage property.
Campbelltown has a long history, and older parts of the area, including around Queen Street and some original farm properties, have heritage-listed buildings. A fence that suits a new estate may not suit a heritage property, and council can require a design that respects the original style. Your planning certificate, described below, shows whether your property is affected.
What Is a Complying Development Certificate for a Fence?
A complying development certificate (CDC) is a fast-track approval for work that meets pre-set standards in the Codes SEPP but isn’t minor enough to be exempt. It can be issued by council or by a registered certifier, usually faster than a development application, as long as the fence meets every complying development standard.
The NSW Planning Portal lists the complying development standards for fences. If your fence fits them, a CDC avoids the longer DA process and neighbour notification. If it doesn’t, a development application is the remaining path.
How Do You Apply for a DA for a Fence in Campbelltown?
A development application for a fence is lodged online through the NSW Planning Portal. You usually need a site plan showing the fence position, elevations showing its height and design, and details of the materials and colours. Council assesses it against its planning controls and may notify your neighbours. Fees depend on the cost of the work.
Check the controls
Look up the zoning and any heritage or bush fire overlays for your property.
Prepare plans
A site plan, fence elevations and material details. Your installer can help with dimensions.
Lodge online
Submit the DA through the NSW Planning Portal and pay the fees.
Assessment
Council reviews the application and may notify neighbours.
Determination
Council approves, approves with conditions, or refuses the application.
Build to the approval
Build exactly as approved, including any conditions.
How Much Does Fence Approval Cost and How Long Does It Take?
An exempt fence costs nothing to approve and can start straight away. A development application has council fees based on the estimated cost of the work, plus the cost of plans, and takes weeks rather than days. A complying development certificate is usually quicker, with fees set by council or the certifier.
| Path | Approval cost | Typical timing |
|---|---|---|
| Exempt development | None | Start once you and your neighbour agree |
| Complying development certificate | Certifier or council fee | Usually faster than a DA |
| Development application | Council fees based on the cost of work, plus plans | Several weeks or more |
Scroll sideways to see the full table.
Check current fees with Campbelltown City Council or the certifier before you lodge. For many homeowners, the time and cost of a DA for a 2.1m fence outweigh the benefit, and a compliant 1.8m fence with planting behind it gives similar privacy with no approval at all.
When an approval is needed, allow for it in your timeline before booking the installation. Installers can usually measure and quote while the application is assessed, so the fence can go in soon after approval.
What Should You Check Before Building a New Fence?
Before building a new fence in Campbelltown, check the height against the exempt limits, the zoning and any heritage or bush fire overlays, the materials and gate direction, any estate covenants, and where the boundary is. Then agree the fence and the cost with your neighbour in writing and get an itemised quote.
Height
Side and rear up to 1.8m, front up to 1.2m, steps on slopes up to 2.2m.
Position
On the boundary for a dividing fence; corner blocks have extra rules on the street side.
Zoning and overlays
Residential, rural or business zone, and any heritage or bush fire mapping.
Materials and gates
Low-reflective, pre-coloured metal; hardwood or non-combustible on bush fire prone land; gates opening inwards.
Covenants
Estate design guidelines and restrictions on your title.
Neighbour and quote
A written agreement or fencing notice, with an itemised quote attached.
If everything on this list checks out, your fence is very likely exempt development and can go ahead. If any item doesn’t, ask council before you build. When you request a free quote, the installer can flag anything at the measure that may need approval.
How Do You Check the Rules for Your Own Property?
Check your property on the NSW Planning Portal, which shows its zoning, heritage listing and other planning controls. A planning certificate from council, which is attached to every contract of sale, lists the zoning and whether the land is bush fire prone or heritage affected. When in doubt, ask Campbelltown City Council.
- Search your address on the NSW Planning Portal spatial viewer (opens in a new tab) to see zoning and overlays
- Look at the planning certificate in your contract of sale for zoning, heritage and bush fire status
- Check whether the NSW Rural Fire Service maps the land as bush fire prone
- Read any estate design guidelines or covenants on your title
- Ask council’s duty planner if anything is unclear
Which council is yours?
Most suburbs in this guide are in the Campbelltown City Council area. Narellan, Mount Annan, Gregory Hills and Oran Park are in Camden Council; Edmondson Park and Casula are in Liverpool City Council; and Appin is in Wollondilly. The state rules are the same, but local planning controls differ.
Do Bush Fire Rules Affect Whether You Need Approval?
Yes. On bush fire prone land, an exempt fence must be built from non-combustible materials or hardwood. A treated pine fence on bush fire prone land isn’t exempt, so it would need approval, and may not be approved. COLORBOND steel and other metal fences meet the rule.
Parts of Kentlyn, Wedderburn, Gilead and Appin, and the bushland edges of several other suburbs, are mapped as bush fire prone. Planning for Bush Fire Protection 2019 sets stricter rules close to homes and at higher bush fire attack levels. Our Colorbond vs timber guide explains the options.
Do Estate Rules or Covenants Also Apply?
Yes. Covenants and restrictions on your land title, and estate design guidelines, are separate from council approval. A fence can be exempt development and still breach a covenant that sets fence types, heights or colours. Check your contract of sale, especially in newer Macarthur estates.
Covenants are enforced by whoever benefits from them, often the developer or other owners in the estate, not by council. They commonly cover front fences, side fence returns and colours. Our Colorbond colours guide covers colour choices that suit most estate guidelines.
Does Council Approval Replace Your Neighbour’s Agreement?
No. Council approval, or a fence being exempt, deals with planning rules. Sharing the cost and agreeing the fence with your neighbour is a separate matter under the Dividing Fences Act 1991. For a dividing fence, you usually need both: the fence must meet the planning rules, and you need your neighbour’s agreement or a fencing order.
Our guide Who Pays for a Boundary Fence in NSW? explains how to agree a fence with your neighbour, serve a fencing notice, and what happens if they won’t pay.
What Happens If You Build a Fence Without Approval?
If a fence needed approval and was built without it, council can order it to be changed or removed, and fines can apply. Unapproved work can also cause problems when you sell. A building information certificate from council can sometimes regularise unauthorised work, but it isn’t guaranteed.
The cheapest approach is to check before you build. If a taller fence is important to you, a 1.8m fence with an approved extension, or a hedge behind the fence, can sometimes give the privacy you want without the approval process.
Frequently Asked Questions
Do I need approval to replace an old fence with the same fence?
Usually not, if the new fence meets the exempt development rules for height, position, materials and gates. Replacing a 1.8m back fence with a new 1.8m COLORBOND fence is a typical exempt project. The Dividing Fences Act still applies, so agree the fence with your neighbour.
Do I need approval for a 2.1m Colorbond fence?
In most residential zones, yes. The exempt limit for side and rear fences is 1.8m, so a 2.1m fence usually needs a development application or a complying development certificate. A 1.8m fence with a short lattice extension also counts toward the height.
Can my neighbour object to my fence?
If the fence is exempt development, there is no approval process for a neighbour to object to, but they can raise it under the Dividing Fences Act if it’s a dividing fence. If you lodge a DA, council may notify neighbours, who can make a submission.
Do I need approval for a front fence?
Not if it is no more than 1.2m high and meets the other rules, including the transparency and pier rules on the street side of a corner block. Taller or solid front fences usually need approval.
Do I need approval for a fence on top of a retaining wall?
Often, because a retaining wall on or near the boundary usually isn’t exempt development, and the combined height may exceed the fence limits. Check with council before building, and see our sloping block guide.
Who approves a CDC for a fence?
A complying development certificate can be issued by Campbelltown City Council or by a registered certifier, as long as the fence meets every complying development standard.
Sources
- Exempt development: fences (NSW Planning Portal) (opens in a new tab)
- Fences: exempt and complying development (NSW Department of Planning) (opens in a new tab)
- State Environmental Planning Policy (Exempt and Complying Development Codes) 2008 (opens in a new tab)
- NSW Planning Portal spatial viewer (opens in a new tab)
- Campbelltown City Council (opens in a new tab)